Month: April 2014

A Modesto Plumber’s Guide On Toilet Replacement

Modesto plumberDo you want a new toilet that has a better flush mechanism? Is your current ceramic throne worn out? Does it have cracks on it? Won’t it flush anymore? Is it no longer pleasing to the eyes? It really doesn’t matter whether you want to replace your toilet for aesthetic or functional reasons. It is your privilege as homeowner to decide on improvement projects to make your home even more comfortable for you and your loved ones. So if you are planning on getting rid of your current john, let us share with you this easy guide on toilet replacement!

Tools & Materials

* new toilet bowl

* rags

* plunger

* adjustable wrench

* hacksaw

* putty knife

* wax seal

* slip-joint pliers

* rubber gloves

* sponge

Instructions

1. Gather your materials. Make sure that you’ll wear rubber gloves to protect your hands

2. Turn off the water supply. Flush the toilet to remove the water that’s left in the system. There will still be a little left inside the bowl so you’ll have to use the plunger to flush it down the drain. Meanwhile, use a bucket and sponge to remove excess water inside the tank. Once done, you’ll have to disconnect the supply line from the base of the toilet tank.

3. Detach the toilet by unscrewing the nuts that connect it to the water supply line. Remove the caps and nuts found on the base of the toilet which are responsible for securing it to the floor. If they’re rusty and won’t let go, cut them off using the hacksaw.

4. Using your putty knife, pry up the throne and get rid of the wax seal that was used to keep it in place. Rock the toilet to loosen it up. Lift it away and place it on some rags. Get rid of the wax gasket and block the drain with another rag to avoid letting the sewer gas seep out.

5. Attach a new wax gasket for the new toilet. Make sure that the flange is still in good condition and that it is secured in place. It’s supposed to connect to a collar that will go through the floor.

6. Replace the wax ring. Doing so will seal the connection and prevent sewer gas from escaping out of the drain.

7. Apply caulk on the base of the new bowl and then remove the rag from the drain opening. Place the new toilet in position, allowing it to sit on top of the flange. Press down. Some even sit on the toilet to squeeze it tightly in place.

8. Tighten the nuts and caps but never overdo it as it may crack the toilet. Insert the tank bolts and gently position the tank over the bowl. Secure the nuts and caps and verify that the tank is level. If it is, put the lid on.

9. Connect the water supply line and tighten the compression valve. Once done, turn the valve on and let the tank fill. At this time, you might want to apply caulk along the edges of the new toilet to make it look pleasing to the eyes. Smoothen it out. You might want to wait a day before you use the new toilet. Test it and if something doesn’t work as it is supposed to, seek the help of a professional plumber.

We hope that this guide is helpful enough to assist you in replacing your toilet. Should you need help with any plumbing issues at home, just hire the most reputed Modesto plumber in Stanislaus County! Plumbers 911 California provides exemplary Modesto plumbing services in CA including toilet repair, plumbing fixture installation, drain line inspection and many more! Call us at 800-731-1139 and we’ll send out our crew immediately!

Having trouble with your clogged toilet? Learn how to use the plunger properly! Watch this video now!

A Modesto Plumber’s Guide On Toilet Replacement first appeared on http://ift.tt/1eVOPvR.

All About Certified and Licensed Plumbers in Miami FL

 

Certified and Licensed PlumberPlumbers often get a bad rap. Their thought of not able to do things right. But reality shows us something completely different. Plumbers are highly experienced professionals who have to undergo special testing methods to prove knowledge in their industry.

Like all professionals, a certified & licensed plumber in Miami Florida undergoes an intensive training. Come to think of it, their superiors won’t throw them on field and let them get their hands dirty if they are not yet ready.

Plumbing company owners make sure that they are hiring the best and qualified plumbing contractors that would build up their reputation. Most importantly, so they can have retainers for long term income.

 

Plumbing Stereotype

“Hot’s on the left, cold’s on the right and shit don’t run up hill.”

That’s what my Father told me when I said I didn’t want to help him with plumbing when I said it would be too hard. He assured me those three things were the only three I needed to know in order to start my, for lack of a better word, internship. Hard work, long hours, exposure to the elements — Some of them man made if you catch my drift — was what I to look forward to. ‘Great,’ I thought.

 

Although licensed plumbing professionals in Miami FL have to undergo intensive internships and preparation, there are those who are not qualified working in the field. These contractors have lower fees, but aren’t really qualifed to handle many plumbing tasks. That’s when homeowners get into trouble, as it necesitates a rework of the task by a certified plumber.

 

How to Choose a Plumber

The best time to choose a plumber is before you experience a plumbing emergency. Unfortunately, most people facing an emergency have very little time to research a plumber. When the toilet springs a leak or the basement ceiling is wet from a broken pipe upstairs, finding help is imperative.

The next time you run across a plumbing contractor give him the Kudos he deserves. When you have a plumbing issue be sure to call a qualified and certified plumber with references. Any licensed plumber is proud of his certification and of the jobs he has performed. He will be glad to furnish references.

 

CLICK VIDEO TO WATCH!

Your Stockton Plumber Talks About Backflow Prevention Devices & Their Importance

Stockton plumberHave you ever experienced getting contaminated water from your taps at home? Have any of your loved ones gotten sick because of bacteria ingestion from your drinking water? If your answer to these questions is “no”, then you must read on and learn all about backflow and its prevention.

What is a backflow?

A backflow is the detrimental reversal of the flow of liquid, solid or gaseous substances from its intended direction which is away from your supply of drinking water. For instance, a backflow happens when wastewater that’s supposed to go to your septic tank or to the sewer system flows into the pipes of your home’s potable water. And this isn’t something to disregard rather a serious problem to attend to right away. Why? Well, a backflow causes water contamination which is not only inconvenient to begin with but also entails health problems. If you aren’t aware that the water you use for cooking and for drinking is already contaminated, you or your loved ones at home may ingest bacteria that can cause diseases. And again, it’s annoying because you won’t be able to use the smelly, yellowish — or sometimes black — water when taking a bath, brushing your teeth or even washing your dishes.

What is a backflow preventer?

Now the good news is, there are backflow prevention devices that can be installed in plumbing systems. A backflow preventer is simply a device that’s designed to safeguard potable water supplies from contamination that results from backflows.

Why is it important to have one installed in your home?

As you may know, a backflow occurs mainly because of cross-connections within your plumbing system. A cross-connection is any potential or actual link between a water supply system and a wastewater system. Such include pipes, valves and even fixtures. The thing is, cross-connections are integral parts of plumbing systems whether residential, commercial or industrial. These connections function properly through air gaps in the system or through backflow preventers. That said, whenever something goes wrong such as an abrupt loss of water, or the pressure drops, a pipe bursts or freezes or even an unusual high demand of water arises, your plumbing system ends up at risk of a possible backflow.

But, if you have a reliable prevention device installed, you won’t have to worry at all. It will ensure that the wastewater from your drain lines will flow as it should be instead of getting into your potable water lines.

We hope that you learned a lot from our blog post for today! Should you need help with backflow device installation, don’t hesitate to call the best and the most trustworthy Stockton plumber in San Joaquin County! That’s us, Plumbers 911 California! We deliver affordable, flawless and excellent Stockton CA plumbing services including commercial drain cleaning, drain line inspection, pipe repair, plumbing installation and many more! Call us at 800-731-1139 so we can assist you!

Want to learn more about backflow prevention? Watch this quick video!

Your Stockton Plumber Talks About Backflow Prevention Devices & Their Importance first appeared on http://ift.tt/1eVOPvR.

Hydro Jetting – A Plumbing Solution With Hydro Power

 A Plumbing Solution With Hydro PowerOops. Someone uses the bathroom and they have to wade through 2 inches of water to get out. You don’t think much of the problem, because, after all, the house has been like that for years. You’ve always had slow moving drains. But beware! This can be an indication of another more serious issue – and you ay need to call in your local Miami Dade County Florida plumbing professional.

 

 

What Can You Do About Drains that Constantly Clog?

I suspect the blockage occurs somewhere beyond the trap, because washing machine water sometimes comes out the bathtub drain. I have used foaming and non-foaming drain unblockers. This has just been money down the drain. I’ve also tried a plunger and a snake, neither of which have worked.P

Is there something else I can try or is it time to call a professional?

Slow drains can be a result of many things including slow draining sewer pipes. But what are you supposed to do about the problem, certainly not use a drain cleaner, this can cause even more problems; issues like corrosion, pipe leaks and more.

No, you don’t want to fix it yourself. You should first call in an experienced plumber  and have him inspect the problem. A simple hydro jetting process could solve the issue. And then, goodbye, slow draining pipes.

Hydro-jet cleaning

Hydro-jet cleaning is a method of cleaning with high pressure streams of water to remove build up and debris in tanks and lines. This process may best be compared to power washing which has also gained popularity as a means to clean driveways, homes, streets, commercial vehicles and more.

 

How Do I Get It Done?

If you think Hydro-jet cleaning is an option for you , your best option is to contact a South Florida plumbing repairman. This is not a project you want to do yourself, and instead, you should get it done by a professional plumping expert. Slow flowing drains are a real pain, but you don’t have to live with the problem any longer. New technologies allow for new repairing methods, and Hydro-jet plumbing solutions is one of these effective methods of cleaning drains of all sorts of debris.

 

Your Angels Camp Plumber Shares How To Install A Garbage Disposal

Angels Camp plumberDid you know that that food waste amounts to 10 to 20 percent of household waste in the United States? In fact, they are an issue when it comes to the municipal garbage disposal. And since food scraps are inevitable components of public waste, the home garbage disposal system was invented. It’s a device that’s electrically powered to grind food waste into smaller pieces so that they can then travel into the drainage pipes and then disposed into a home’s septic tank system or the local sewage treatment facility. The garbage disposer truly has a lot of environmental benefits as much as they also make our lives more convenient. So if you are planning to have one installed in your sink or if you need to replace your current machine, let us share this DIY guide with you!

Installation:

1. Detach the drain pipe and the strainer from the sink. If you have a two-bowl sink, just remove the drain pipes and the strainer from the bowl where you’ll attach your garbage erator.

2. Form a snake shape with your plumbers’ putty by rolling it between your hands. Run it along the base of the machine’s flange that is included in the package. Place the same flange in the drain hole where you removed the strainer and the pipe. Secure it.

3. Attach the gasket and the mounting rings on the flange. There’s supposed to be two: upper mounting ring and lower mounting ring. Once they’re in position, attach the retaining ring, too. Secure the screws using your reliable screwdriver. Trim the excess putty that’s squeezed out from the connection and clean your sink.

4. Connect the garbage disposal system to the flange by following the user’s manual and installation guide that came with it.

5. There’s a discharge opening located at the side of the garbage disposer. Attach the discharge tube to it by utilizing a gasket or washer that’s included in the package.

6. Install the drain pipe once again. If you have a two-bowl sink, simply utilize a single P-trap by running the discharge tube from the garbage erator to a T in the drain pipe.

Important Tips Before Installation:

Don’t forget to wear protective clothing such as gloves and dust mask. Also make sure that the power is off before installation to prevent accidents. Before usage, it is wise to have a professional check on your work. This will ensure that you’ve installed the system correctly.

We hope that you found this guide helpful when installing your garbage disposal. But to guarantee proper and safe installation of your plumbing appliances, it is best to call the most trustworthy Angels Camp plumber! That’s us, Plumbers 911 California! We provide exemplary, immediate, safe and affordable Angels Camp plumbing services in Calaveras County CA including drain pipe cleaning, plumbing repair, pipe repair and many more! Call us at 800-731-1139 so we can assist you!

Want to learn how to fix a leaking garbage disposal? Watch this video!

Your Angels Camp Plumber Shares How To Install A Garbage Disposal first appeared on http://ift.tt/1eVOPvR.

Arnold City Plumbing Tips For Spring Cleaning

Arnold City plumbingWe all have heard the saying that spring is a time for new beginnings. Indeed, it is a season of growth, color and life. And from this, we have coined the concept of spring cleaning. We spend hours if not days cleaning the house thoroughly regardless if we’re actually living in a cold area or the otherwise. Because it is spring and the weather is fair, we spend our time productively by doing a general and heavy-duty home cleaning. We re-arrange the furniture or get rid of things that we don’t need. Some even repaint or start home improvement projects. However, we want to know one thing. Do you even bother to check your plumbing? We hope so! Here’s a short list of tasks you might want to follow!

1. Check your taps for leaks. And when we say taps, we mean all of them. Check your kitchen faucets, outdoor faucets, tub faucets. Try them out and observe if there are leaks. If there are, have them repaired. You surely do not want to incur high fees on your utility bills moreover waste water.

2.  You have to find out if the cold season has caused burst or broken pipes. If it has, then you should have the affected pipes repaired.

3. Inspect your water heating system. Look around for signs of corrosion, moisture or leaks. Is it still heating water in a rate that it’s supposed to? If not, you might want to have it checked. Also remember to lower down the temperature. Since the weather’s no longer that cold, heating will no longer be difficult for the machine.

4. Make sure your water supply valves are working. Test them out by turning them on and off. Doing so will prevent them from getting stuck.

5. Clean your shower head. It is not impossible that debris may have built up in the past few months. Get rid these mineral deposits by using vinegar.

6. If you have a sump pump at home, test it. Pour water and then turn the pump on to ensure that it works just fine.

7. Install flood alarms. If you live in an area that’s flooded frequently, now is the perfect time to install your flood alarms.

8. Inspect your gutters and downspouts. It’s possible that animals may have taken shelter in them during the winter so you have to make sure that they’re no longer staying there.

9. Install drain screens and strainers if you don’t have any. They’ll prevent clogs which will prevent a lot of inconvenience and unwanted expenses.

We hope that these tips are valuable enough to help you on your 800-731-1139 and we’ll assist you right away!

Want to learn more spring cleaning tips? Watch this video!

Arnold City Plumbing Tips For Spring Cleaning

Your Sonora Plumber Gives Tips On How To Fix Low Water Pressure

Sonora plumberYou wake up early to get ready for work only to find out that the stream of water is too little for you to take a bath comfortably. You can’t even prepare breakfast because the kitchen tap is merely dripping. You use the toilet and apparently, you have to fill the pail for an hour so that you can flush your ceramic throne. Quite an inconvenience, isn’t it?! What you’re experiencing is low water pressure or low flow. And do you know what causes such an annoying problem? Well, there are many things. It could be because of mineral deposit build-up; malfunctioning water valves; a leak somewhere in your plumbing system; a nasty clog or pressure regulators that must be configured. To help you put an end to the issue, let us share this troubleshooting guide with you.

1. Check your fixtures’ aerators first. Hard water contains minerals that can accumulate over time. Make sure that there aren’t build-ups in your faucets or showerheads. If cleaning them doesn’t resolve the problem, double check the supply valve or the piping.

2. If the problem is coming from a single tap, observe it. Is it corroded? If it is, then replacement may be the solution. You can also disassemble it to check if it has loose or broken parts.

3. In most instances, supply valves turn accidentally. This is normal especially if the pressure is naturally high in your plumbing system. It might have moved or turned off without you knowing it. Turn it and see if it makes any difference.

4. Clogs in your supply pipes may also result to low flow. Clogs may be caused by objects that get into the system, minerals that build up, roots that obstruct the lines or even organisms such as algae or mold. If cleaning out your faucet heads and shower heads don’t alleviate the situation, jetting may be the answer.

5. A broken pressure regulator may also lead to low water flow. However, you might want to seek the help of a professional right away because they’re the ones who are skilled to diagnose and fix this problem.

6. Low pressure from the main water source is also another factor to consider. If your plumbing system at home is okay, you might want to get a pressure gauge and check the water pressure. If it is low, call your water provider so that they can verify the cause of the inconvenience and have it fixed if they’re responsible.

7. When all DIY troubleshooting fail, call your trusted plumbing professional.

We hope that you learned well from our blog post for the day! Should you need the advice and help of a Sonora plumber, just call Plumbers 911 California! We provide top-of-the-line plumbing services in Sonora CA including pipe repair, faucet repair, drain pipe cleaning and many more! Call us now at 800-731-1139!

Are you wasting so much water because of your old toilet? Learn how to lower down the water flow! Watch this video now!

Your Sonora Plumber Gives Tips On How To Fix Low Water Pressure first appeared on http://ift.tt/1eVOPvR.

A Plumbing Maintenance Checklist From Your Trusted Jamestown Plumber

Jamestown plumberYou rely on your plumbing everyday: whenever you take a bath; whenever you answer the call of nature; whenever you cook food for your family; whenever you clean the house or your car; whenever you bathe your pets and many more. And because you rely on it, it is only necessary that adequate and proper care is due. Do you know that consistent and prompt plumbing maintenance can do wonders for your home? A simple cleaning of your toilet every week; annual flushing and draining of your water heater tank or preventing food items from going into your drain can thwart the onset of plumbing problems and steer you away from unwanted repair expenses.  To help you care for your plumbing system, let us share with you these indispensable tips!

1. High pressure isn’t good for your plumbing system. It may stress out your plumbing lines, cause high levels of mineral deposits and may even result to pipe bursting. To ensure that the pressure is right, measure it using a pressure gauge or have it checked by a professional.

2. Garbage disposal systems are sensitive pieces of equipment that make your life in the kitchen a lot easier. Take good care of it by not throwing in large pieces of food items or objects. Also remember not grind hard objects such as metal or wood. Note that it’s only for biodegradable items which are easily broken down into smaller pieces and can decompose.

3. When cleaning drains or ridding them of clogs, only use natural remedies instead of toxic cleansers. Excessive and frequent use of harsh chemicals may destroy your pipes.

4. Hard water may cause debris buildups in your plumbing systems and faucets are no exception. Check their aerators once in a while to ensure that debris are removed regularly.

5. Leaks don’t pose big problems unless neglected. When you notice leaking under your kitchen sink, in the walls, in the basement, in your toilet or anywhere else in your house, attend to it right away. Doing so will not only save you from shelling out more money on utility expenses but also thwart the possibilities of graver damages and unreasonable repair costs.

6. Flushing your water heater tank annually or even twice a year will not only lengthen its life span. Doing so will also make it work more efficiently.

7. Regular septic tank cleaning is recommended. Seek the help of professionals to have it pumped out every three to four years or even more depending on your household needs. Avoid flushing objects down the toilet such as sanitary napkins, soap or even toilet paper.

We hope that you learned much from our blog post! And should you need help with home or commercial plumbing, just call your reliable Jamestown plumber! Plumbers 911 California delivers only the best Jamestown CA plumbing services such as plumbing repairs, pipe repairs, water heater service and many more! Call us now at 800-731-1139 and we’ll send out our crew right away!

One of the plumbing fixtures you should take care of is your toilet! Watch this video to learn how to fix it!

A Plumbing Maintenance Checklist From Your Trusted Jamestown Plumber first appeared on http://ift.tt/1eVOPvR.

Why Your Phoenix Lake Plumber Is Not An Average Plumbing Guy

Phoenix Lake plumberRegardless if your home is old or new, there will still come a point in time when you’ll need help in fixing leaky faucets, clogged toilets, burst pipes, septic tank backups and many other plumbing problems that may drive you crazy and panicky. There are just too many kinds of plumbing emergencies that you’ll experience as a homeowner and the thing is, you just can’t tell when they’re going to happen. That being said, you’ll need a reliable plumbing expert who will be there to assist you during such crises. You’ll need your Phoenix Lake plumber — Plumbers 911 California. Why us? Well, we are not your average plumbing guy and here are some reasons to back our statement up!

1. We’re just a call away.

The problem with plumbing emergencies is that they’re unpredictable! Fortunately, we are always available to help you out. Dial our number during the day or in the wee hours of the night, we guarantee that there will always be someone to attend to your call. In other words, we operate 24/7!

2. We’re highly trained.

We don’t put up with mediocrity. To make sure that we’ll provide flawless services to our customers, our plumbers are continuously undergoing extensive trainings especially when there are new technologies, techniques and methods to learn.

3. We are experienced.

We have serviced a great number of clients and have solved thousands of plumbing problems in the US. We’ve received plenty of testimonials from loyal customers who attest not only to our high-quality performance but also to our professionalism, integrity and work ethics.

4. We only hire drug-free plumbers.

We understand that letting someone you don’t know inside your home is not easy. But don’t you worry. We are proud to say that our plumbing technicians are all drug-free. We value our customers so much which is why we see to it that your properties as well as your safety won’t be compromised because of irresponsible plumbers.

5. We offer a broad array of services.

We won’t give you any reason to move on to the next plumbing company. We are confident that we can help you out in any plumbing problem that you might encounter. Whether you need a new plumbing installation, repair services, remodeling assistance or what-not — you name it, we can do it!

We hope that we have given you enough reasons to believe that your Phoenix Lake plumber is not your average guy. Plumbers 911 California provides affordable, flawless and first-rate Phoenix Lake plumbing services that aren’t limited to just plumbing repairs! We can also help you out in terms of water heater service in Central Valley, drain line inspection, plumbing installation and many more! Call us at 800-731-1139 and we’ll send our team out immediately!

Want to learn more about us? Watch this quick video!

Why Your Phoenix Lake Plumber Is Not An Average Plumbing Guy first appeared on http://ift.tt/1eVOPvR.

How To Repair Different Types of Faucets

faucet repairs sonoraWe’re pretty sure that you have experienced having leaky faucets, continuously flowing taps or broken spigots at home especially if you’ve been using the same one for such a long time already. If you haven’t, then you’re definitely a lucky homeowner. Although leaks, continuous flows, lose threads and broken faucets aren’t that big of a problem, they still need to be attended to because you rely on them every day. However, you should know that there are several types of faucets and each of them requires a slightly different way to get repaired. Since every kind is comprised of unique parts and designed variedly, you’ve got to have adequate know-how to be able to succeed in DIY plumbing repairs. Let us help you through our blog post for today.

Different Types of Faucets And How To Repair Them

1. Cartridge-Type Stem Faucets

These kinds of faucets have rubber washers and springs. You can replace them by detaching the cartridge out of the tap’s body and then removing the spring and washer. Once they’re out, insert the new parts and carefully align the cartridge again. When it’s already perfectly positioned into the slots, secure it.

2. Faucets With Rubber Seat Rings

These types of faucets use a rubber seat ring instead of a washer. Remove the ring from the faucet stem and using your reliable pliers to hold the body, unscrew the threaded center part that secures the seat ring. Detach the sleeve and insert a new seat ring. Re-assemble the faucet back to its original setup.

3. Faucets With Metal Discs

These types don’t have washers. Instead, they make use of two metal discs that allow water to flow through the system. When this kind of faucet leaks, drips or malfunctions, the valve assembly must be changed.

4. Faucets With Built-In Seat Rings In The Stem

These kinds of spigots also have washers but their seat rings are built in to their stems. To repair this kind of faucet, simply unscrew the stem nut from the stem base. Remove the metal discs and the washer retainer that’s equipped with a rubber washer. Install the new washer into the retainer and assemble it back.

5.  Faucets With Rubber Diaphragms

While there are faucets that use rubber washers or metal discs, there are those that are equipped with rubber diaphragms to control the water. Just remove the stem using your handy pliers. You’ll find a rubber diaphragm at the bottom of the stem which you’ll have to pry open with the help of a screwdriver. Replace the diaphragm and ensure that it’s positioned perfectly before reassembly.

6. Single-Lever Faucets

There are so many types of single-lever faucets and you won’t find it hard to repair them. Why? Because there are kits for specific brands and types of this tap. Just get the right repair kit from the hardware store and follow the instructions.

We hope that you learned a lot about fixing different faucet types from our blog post. Should you need faucet repairs in Sonora CA, just call a reliable Sonora plumber to help you! And that’s us, Plumbers 911 California! We provide 24-hour plumbing repair services including drain line inspection, plumbing installation and more! Call us at 800-731-1139 and we’ll send our team out immediately!

Want to learn how to fix a leaky ceramic faucet? Watch this video!

How To Repair Different Types of Faucets first appeared on http://ift.tt/1eVOPvR.